EverFocus EPTZ3600 Manual de usuario

Speed Dome EPTZ3600/EPTZ3600I USER MANUAL Date: Jan. 2009

10 1.3.2. EPTZ3600/EPTZ3600I Base Board The base board that is inside the top housing connects to power cable, video cable, control cable, alarm c

11 Pin # Function 1 ALM_NO_B (Alarm Output Normal Open B) 2 ALM_COM_B (Alarm Output Common B) 3 ALM_NC_B (Alarm Output No

12 1.4. EPTZ3600/EPTZ3600I Quick Operation Guide (Work with EKB500) EPTZ3600/EPTZ3600I and EKB500 (Keyboard) can work together by using factory defa

13 2. EPTZ3600/EPTZ3600I INSTALLATION 2.1. Packing List There are 3 boxes that are camera main body with a camera module, top housing with a base b

14 * EKB500 (Keyboard) * EKB200 (USB Controller Keyboard)

15 2.2. Cable Needed Power Cable An adapter with 24VAC/3.5A output provides the power to the EPTZ3600/EPTZ3600I. An extension power line may be nee

16 terminal resistance settings. All of the settings should be confirmed before the dome is installed. The control-related setting that is address,

17 Note: You will see the label of Protocol & Baud Rate as well as RS-485 ID address show on the speed dome. White part represents the s

18 ON1 2 3 4 5 6 7 8Switch Address1ON1 2 3 4 5 6 7 82ON1 2 3 4 5 6 7 83ON1 2 3 4 5 6 7 84ON1 2 3 4 5 6 7 85ON1 2 3 4 5 6 7 86ON1 2 3 4 5 6 7 87ON1 2

19 ON1 2 3 4 5 6 7 8Switch Address129ON1 2 3 4 5 6 7 8130ON1 2 3 4 5 6 7 8131ON1 2 3 4 5 6 7 8132ON1 2 3 4 5 6 7 8133ON1 2 3 4 5 6 7 8134ON1 2 3 4 5

2 Table of Contents 1. EPTZ3600/EPTZ3600I OVERVIEW...5 1.1. Introduction ...

20 2.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits are used to set communication protocol. The factory default protocol is EVF.

21 2.4. Bracket and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and sh

22 2.4.2. EPTZ3600 Dome Camera Wall Mount Simple Installation 1. Screw the top housing to bracket by using a hexagon wrench. 2. Put the water

23 3. Connect the cable you detached from base board to the RS485 cable, Power cable and video cable you thread from the wall or ceiling. RS485 cabl

24 5. Screw in 4 long screws to fix the bracket to bracket base.

25 Pull here to open 2.4.3. EPTZ3600 Dome Camera Wall Mount Installation Note: Installation location that is a wall, a pole or a ceiling needs t

26 Pull open this switch 2. Apply the adhesive stripe at back of desiccant pack to the inner side of the top housing. There are totally 3 desiccant

27 4. Put the waterproof silicon pad on top of the base board for waterproof purpose. 5. Connect the cable you detached from base board to

28 6. Screw in 4 screws for mounting the bracket base. 7. Thread the cable through the bracket.

29 8. Screw the top housing to bracket by using a hexagon wrench. 9. Screw in 4 long screws to fix the bracket to bracket base.

3 3. EPTZ3600/EPTZ3600I CAMERA SETUP MENU...38 3.1. Structure of the Setup Menu ...

30 10. Pull the hole of base board to open it again. Connect the power and RS485 wires back to power pin and RS485 pin. If you need to connect alarm

31 Note 1: When you push the orange buttons to detach the main body from bracket, please hold the main body carefully, otherwise it may fall down

32 Note 1: In order to protect the bubble from dirt and scrape, please put on the gloves before installing the bubble. Note 2: The camera module on

33 2. Screw the 3 screws of EPTZ top housing to the 3 holes of indoor recessed mount bracket. 3. Put the indoor recessed mount bracket to the h

34 5. Snap main body to the indoor recessed mount bracket. NOTE: Aim the Arrow label of the main body to the same Arrow label of the bra

35 7. Aim bracket’s fillister to surface ring’s fillister, turn it until it is firmly fixed.

36 2.5. Bracket & Adapter 2.5.1. Indoor Ceiling Pendent Mount Bracket The indoor ceiling pendent mount bracket is used for installing a

37 2.5.3. Corner Mount Adapter The corner mount is used for installing a wall mount bracket to a 270° corner of walls indoors or outdoors. 2.5.4

38 3. EPTZ3600/EPTZ3600I CAMERA SETUP MENU In this section, setup and operation guide of EPTZ3600/EPTZ3600I will be introduced. There are 9 items o

39 3.2. VIDEO SETTINGS In main menu, turn joystick Up / Down to select VIDEO SETTINGS. Turn joystick Left / Right to enter VIDEO SETTINGS sub-menu (

4 3.5.6. POWER UP FUNC...60 3.5.7. AUTO FLIP...

40 There are 4 options in Exposure: EL. SHUTTER, SLOW SHUTTER, IRIS MODE, and AE SPEED. EL.SHUTTER: Select electronic shutter mode from the options

41 AE SPEED: if you select AUTO in slow shutter, you can set exposure time (move the cursor between 0~6) EXIT: Select Exit to save settings and exi

42 the entire screen. It outputs the proper value using the color temperature radiating from a black subject based on a range of value from 3000 to

43 3.2.7. COLOR: In Color, we define color of the image. Select from ON and OFF. ON: Color image OFF: B/W image 3.2.8. NEGATIVE In Negative mode,

44 3.3. POSITIONS In main menu, turn joystick Up or Down to select POSITION option. Press Enter key or turn joystick Left / Right to enter POSITION

45 (diagram 3.6) POSITION: Select from SET and CLEAR. SET: Select SET and press Enter key of keyboard, you will be entered to a sub-menu. Turn t

46 SPEED: Select the speed for the preset position. The value is from 1 to 255 and 255 is the highest speed. DWELL TIME (S): Select the dwell t

47 3.4. OSD/AREAS In main menu, turn joystick Up or Down to select OSD/AREAS. Turn joystick Left or Right to enter OSD/AREAS sub-menu (see diagram 3

48 In zone menu, you can set a zone and name it, when the speed dome turns to the zone you set, it will display zone name on the screen (only if “O

49 Turn joystick Right/Left to highlight the zone you have set and turn the joystick Up/Down to select another zone number. If you wish to clear the

5 1. EPTZ3600/EPTZ3600I OVERVIEW 1.1. Introduction EPTZ3600 series has 2 types, EPTZ3600 is outdoor type whereas EPTZ3600I is indoor type, using

50 3. Press IRIS+ key of keyboard to save and return. 4. Go to “DEFAULT NORTH” and press Enter key to set the north position as default north pos

51 1. SHOW OSD ON: show OSD of Camera Title, Directions, Zones, Preset Title, Motion, Zoom, Fan and Camera Status. OFF: do not show OSD. 2 SEC: sho

52 NO: do not show zoom multiple. 7. FAN YES: show fan indication when fan is enabled. NO: do not show fan indication. 8. MOTION YES: show motion

53 (diagram 3.16) 3.5.1. AUTOPAN Press Enter key of keyboard or turn joystick Left/Right to enter AUTOPAN sub-menu (see diagram 3.17) (diagram 3.1

54 Select speed from 1~255 and 255 is the highest speed. c. DWELL TIME L (S) Select dwell time of the left position from 1~99 seconds. d. DWELL TIME

55 (diagram 3.19) g. DEFAULT ON: all settings in AUTOPAN menu will be returned to default values. OFF: the setting in AUTOPAN menu is not defau

56 (diagram 3.20) a. Tour NO.: Turn the joystick Left/Right to select tour number first b. POS: Turn the joystick Left/Right to select preset pos

57 3.5.3. PATTERN Press Enter key of keyboard to enter PATTERN sub-menu (see diagram 3.21) (diagram 3.21) a. Turn the joystick Up or Down to sele

58 e. When you return to PATTERN SETUP menu, turn the joystick Left/Right to PLAY. Press Enter key of keyboard. The camera starts to run the patter

59 (diagram 3.24) 3.5.5. RESUME TO Turn the joystick Left/Right to select the mode to resume to. It is selectable from PREV MODE, POS.1 (H), T

6  192 preset positions are available.  16 cruise tours can be set, and each tour contains up to 16 positions.  Up to 256 speed domes can be s

60 3.5.6. POWER UP FUNC Turn the joystick Left or Right to select the mode to return to when power failure occurs. It is selectable from PREV MOD

61 3.5.8. EXIT Exit from the current menu. 3.6. ALARM In main menu, turn joystick Up or Down to select ALARM. Turn joystick Left or Right to enter

62 event triggered, the camera will be changed to day mode. OFF: Disable alarm input. (diagram 3.29) c. REACTION: The action will be taken when ala

63 TIMEOUT: Turn the joystick Left or Right to select on TIMEOUT and press Enter key to select time-out. Time-out is selectable from 1~99. Press En

64 3.6.2. ALARM OUTPUTS Press Enter key of keyboard to enter ALARM OUTPUTS sub-menu. (see diagram 3.30) (diagram 3.30) a. OUTPUT NUM: Select Out

65 Select NO to disable this function. i. RETURN: RETURN to the previous menu. 3.6.3. MOTION DETECT Press Enter key of keyboard to enter MOTION

66 is represented by pink, Motion 2 by blue, Motion 3 by green and Motion 4 by yellow. Press IRIS+ key to save setting and return to previous menu.

67 3.7. PRIVATE ZONES In main menu, turn joystick Up/Down to select PRIVATE ZONES masking. Turn joystick Left/Right to enter PRIVATE ZONE sub-menu (

68 c. Select the area to be covered first. Turn joystick Left/Right to adjust width of the private zone area. Turn joystick Up or Down to adjust h

69 3.8. SYSTEM In main menu, turn joystick Up/Down to select SYSTEM. Turn joystick Left/Right to enter SYSTEM sub-menu (see diagram 3.36) (diagram 3

7 1.2. Specifications Product Model EPTZ3600 (outdoor) EPTZ3600I (indoor) Pickup Device SONY 1/4” EX-view HAD CCD Video Format NTSC or PAL Sca

70 -PASSWORD ACTIVE: Select YES to activate password mode. Select NO to disable password mode. -ENTER PASSWORD: Enter the password -VERIFY PASSWOR

71 c. BAUDRATE: shows baud rate of this speed dome d. RS-485-ID: shows RS-485 ID of this speed dome e. PRESET-CNT: Preset counter. This counter c

72 4. EPTZ3600/3600I FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode  Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockw

73 4.3. Position Setting  Focus on a preset position: Press the number key, and then press Position to focus on the number of preset position; or

74 speed. Dwell time: default is 2 sec; It can be changed by EVF Keyboard Set + A.Pan setting dwell time of A pos or B pos. 99 => Auto scan (360

75  One-way tour Mode: Press Tour to enter the tour mode. The system will ask you to enter the tour number you would like to run, and starts the t

76 If you set the position number to 99, the dome will do a 360 degree auto scan or AB two point pan if limit is ON. If you set the position number

77 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380

8 Horizontal Rotation Speed 0.01°/s －360°/s (1-255 grade shift gears) Horizontal Rotation Range 360° unlimited rotation Tilt Rotation Range 180° pe

9 1.3. Feature 1.3.1. Profile of EPTZ3600/EPTZ3600I Wall Mount Bracket Sun shield (optional) Bubble Camera main body Top housing Camera module O