EverFocus EPTZ Series Manual de usuario

Speed Dome EPTZ1000 USER MANUAL Date: Aug. 11th, 2005

2-9Note: The input AC voltage range of an adapter depends on different area. Please make sure the voltage range before installing. Video Cable

2-102.3.1. Address Setting The address code of the EPTZ1000 should be set to correspond properly with a control device to control multiple dome camer

2-11ON12345678Switch Address1ON123456782ON123456783ON123456784ON123456785ON123456786ON123456787ON123456788ON123456789ON1234567810ON1234567811ON123456

2-12ON12345678Switch Address129ON12345678130ON12345678131ON12345678132ON12345678133ON12345678134ON12345678135ON12345678136ON12345678137ON12345678138O

2-132.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits of the SW2 are used to set communication protocol. The factory default protocol

2-142.3.4. Video Format Setting The 6th bits of the SW2 on the PCB board are used to set the video format. The default video format depends on the fa

2-15CAM-0 CAM-1 CAM-nKeyboardDVRRS485Control Unitn ¡ Ø 255TernimatorResistanceON Note: When the dome is out of control, or does not work under contr

2-162.4. Rack and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and shoul

2-17 2. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket. 3. Take off the housing from

2-185. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwi

1-1Table of Contents 1. EPTZ1000 OVERVIEW...1-3 1.1. Introduction ...

2-19 Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 7. Turn on the power, and start

2-202.5.3. Corner mount The corner mounts are used for installing a wall mount bracket to a corner of walls indoors or outdoors. There are two

2-212.5.5. Ceiling mount The ceiling mount is used for installing a speed dome on the ceiling indoor. 2.5.6. Embedded ceiling mount The embedded

3-223. EPTZ1000 CAMERA SETUP MENU In this section, setup and operation guide of EPTZ1000 will be introduced. There are 22 items of the setting menu.

3-233.1.1. Camera Setup Menu Press MENU to enter camera setup menu. Shift Joystick up/down to change subentries, and right/left to change the setting

3-247. ICR Day/Night Mode auto switch. The speed dome will auto switch to night mode, and display in B&W (Black and White) mode to increase the

3-25MAN: Manual white balance mode. 13. TITLE DISPLAY : Display the title. ON: Enable title display. OFF: Disable title display. 14. AUTO FLIP Fl

3-26N.O.: Enable a normal open alarm input. N.C.: Enable a normal close alarm input. OFF: Disable alarm input. 19. ALM-IN PRIO The priority of

4-274. EPTZ1000 FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode ¾ Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/C

4-28then press Shift + Position. The system will ask you to enter the preset position number (1~239), and then press Enter to save the position. Ther

1-22.5.3. Corner mount ... 2-20 2.5.4. Pole mount ...

4-29Note: The difference between the One-way tour mode and To-and-fro tour mode is that the return modes are different. For example: There is a tour

4-30RELAYJP6JP4JP3 JP1JP5Video +Video -RS485 +RS485 -AC24AC24JP51 ~ 9APPENDIX A: The Alarm I/O Connection There are 4 alarm inputs and 1

4-31 P/N : MW01G00400 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TE

1-31. EPTZ1000 OVERVIEW 1.1. Introduction EPTZ1000, an intelligent high-speed dome camera is ready to secure your property with its omni-directional

1-4 All of the features make the intelligent high-speed dome camera works for a wide range and demanding application such as banks, airports, station

1-5and JP3 are connectors for heater, and they can be switched. JP6 is a fan controller connector that turns on/off of the fan. The 3 cables are too

1-61.3. EPTZ1000 Connection Alarm 1Alarm 4Alarm 3Alarm 2GROUNDRS485 Tx(+)RS485 Tx(-)24V AC110V ACVideo OutPOWER24V AC / 3.5 ABNC1.0Vpp ¡Ó 0.2V, 75RS4

1-71.4. EPTZ1000 Quick Operation Guide (Work with EKB500) EPTZ1000 and EKB500 (Keyboard) can work together by using factory default setting. You jus

2-82. EPTZ1000 INSTALLATION 2.1. Packing List There are 3 boxes that are housing, bulb and mechanical part with a camera module, one wall mount brack