EverFocus IP66 Especificaciones

Operation Instruction IIRR DDaayy//NNiigghhtt pplluuss WWiiddee DDyynnaammiicc RRaannggee IIPP6666 BBuulllleett CCaammeerraa EEZZ

10 Dimension of whole camera with bracket Dimension of whole camera with bracket and EPR100 275mm/10.8” 1

11 1.5 Camera Component Description EZ650 Component description Bracket Sun shield Fixing screw for sunshield Vi

12 1.6 Back Panel Layout 1. Video Output Connector Connect the video output of the camera to a color monitor or oth

13 5. Control key selection switch Switch to OSD to control OSD menu by using the control key or switch to LENS to adjust zooming and focus (please

13 2. Installation This chapter will describe, in general terms, how to install the EZ650 camera. STEPS: 1. Wire and mount the camera. See 2.1 2

14 2. Fix the bracket to wall by using 4 screws. 3. Open camera’s back cover: Loose the 2 screws from the back panel cover, then open

15 4. Take off the cap of waterproof conduit which is at the camera bottom. Note: 1. the holes of waterproof conduit were plugged, pleas

16 Note: 1. Power cable’s diameter must be less than 10 mm 2. Only use RG59/5C2V for Video cable 3. RS485 cable must be less then 5 mm 6. Clo

17 8. Connect RG59 coaxial cable with BNC connector. 9. Unscrew both cable clips, wire power cable and RS485 cable through the cable clips. The

18 2.2 Adjusting Camera Position Adjust camera’s angle vertically or horizontally by using hex key included in package.

2 EVERFOCUS ELECTRONICS CORPORATION P/N: 4605XZ0650001AR Operation Instruction  2008 EverFocus Electronics Corp Please read this manual fir

19 2.3 Adjusting Lens Open camera’s base, a control key is attached at inner side of the base. Detach the control key and use this key for OSD or L

20 2.4 Keyboard Connection (Optional) Please refer to Chapter 4 for more details of Keyboard control. 1. Connect the cable from keyboard’s R

21 3. OSD Menu & Configuration This chapter introduces how to configure the camera OSD menu. 3.1 Control Key General Operation Guide Please tu

22 When the item with sub-menu is selected, press the mini-joystick to switch to the sub-menu for further settings. Please refer to the diagram belo

23 3.2 RS485 ID & Baud Rate Setting Note: This section is optional preserved for the people that want to change camera ID and baud rate. In mos

24 b. RS485_ID- adjustable 01~128. Default value is 01. Move joystick RIGHT and LEFT to adjust it. RS485 ID of EZ650 has to be the same a

25 d. DATA STORED- Confirm with you that the last 3 settings you have made will be saved. e. ENTER_SET_MENU- press the mini-joystick

26 3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets. Lens — DC — Brightness 0~100 (50) Expos

27 — Motion — Off — On — Area Select — Area1-Area4 — Area Display — Off, On — Left/Right — 5~66 — Width — 0~9

28 3.3.2 LENS When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris

3 Precautions 1. Do not place any object on top of the cover. 2. Be careful when handling the camera, do not drop it or subject it to strong shock

29 3.3.3.4 BLC-BACKLIGHT COMPENSATION There are three choices for the type of BLC which may be employed: OFF, traditional BLC or

30 1. Please direct the arrow to point to “BLC” by using the UP and DOWN buttons. 2. Select the HSBLC mode by pressing the LEFT or RIGHT button. Th

31 3.3.4 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function. Please direct the arrow to point to “WHITE BAL

32 Press “RET” to save all settings in the DAY/NIGHT menu and returns to the previous menu. Press “END” to save all the setting menus and exit.

33 Please direct the arrow to point to “CAM TITLE” by using the UP or DOWN button. Select “ON” by pressing the LEFT or RIGHT button. Press SETUP but

34 3.3.7.5 D-ZOOM Setup for digital zoom. OFF Disable the D-ZOOM function ON D-Zoom: Select digital zoom from X1.0 up to X32. Note that zoom level

35 the sensitivity value is high, motion detection sensitivity increases to sense very small movements and vice versa. MOTION VIEW Select “ON” to

36 3.3.8.1 SHARPNESS The contour of the video image becomes cleaner and more easily distinguished as the level of SHARPNESS increases. If the level

37 Control from Keyboard EKB500 (Optional) Note! Before being able to control keyboard, make sure Keyboard RS485 camera ID, Baud rate match the c

38 d. Move the joystick RIGHT () and LEFT () to adjust the mode and parameters of the selected item. e. Press “Menu” to leave and goes to pre

4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital de

39 EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2

5 Table of Contents 1.1 FEATURES...

6 1. Product Overview Achieve long range surveillance with clarity in virtually any lighting conditions. The amazing low light sensitivity of 0.05

7  Motion detection for 4 configurable zones.  Privacy mask function for 8 configurable zones.  Provides digital zoom up to 32x.  Cables rou

8 1.3 Specifications Product Model EZ650 Pickup Device 1/3” SONY Super HAD CCD Ⅱ Video Format NTSC or PAL Picture Elements 768 x 494 (NTSC)/752

9 1.4 Dimensions Drilling Dimension of holes to holes Dimension of Bracket 45mm/1.8”80mm/3.2” 220.5mm/8.68”84mm/3.31”106.5mm/4.19112.7mm/4.